Supermatic® User Manual with a stylized graphic.
User manual for Supermatic® helmet with a sleek design.

Before Your Start

In the Box

2x Bindings
2x Offset Mounting Disks
Older disks feature a triangular hole in place of the arrow
8x Screws
1x Leash

Tools Needed

Size 3 Phillips Head Screwdriver (PH3)
2x Offset Mounting Disks
8x Screws
1x Leash

Mount Your Bindings

1. Access the mounting disk: loosen the footbed screw, slide the footbed to the front and remove.*
*For size small, screw is located at side; lift adjacent corner before sliding footbed forward.
2. Orient the mounting disk according to your snowboard’s insert type (4x4 or Channel). Flip it 180° to reduce either toe or heel overhang.
2x Offset Mounting Disks
8x Screws
1x Leash
3. Rotate the disk to your desired angle. Each notch is 3°.
4. Mount the binding to your snowboard using the supplied screws. Ratchets should be on the outside of your foot when in the binding.
2x Offset Mounting Disks
8x Screws
1x Leash
5. Place boot in binding and check it’s centered over the board. If not, loosen the screws and re-adjust the disk (see point 2).
6. Slide the footbed back onto the baseplate and screw down. Choose the position that best matches your boot length.
2x Offset Mounting Disks
8x Screws
1x Leash

Adjust Your Straps

1. IMPORTANT: Push the heel pedal down until it is fully locked, with the highback in the upright position.
2. Loosen the straps on both sides and place the boot into the binding. The toe strap should go over the corner of the boot.

*For models featuring the Hexo Toecap 2.0, toe straps can be switched between the left and right foot for a better fit with larger boots.

2x Offset Mounting Disks
8x Screws
1x Leash
3. Center the straps over the boot.
4. Lock down the QuickSet buckles on the inside, and tighten the Locking System Ratchets (LSR). Check that the straps are centered.
2x Offset Mounting Disks
8x Screws
1x Leash
5. Adjust the diagonal ladder using the QuickSet buckle.
IMPORTANT: Leave some space between this strap and the boot to enable smooth entry and exit.
2x Offset Mounting Disks
8x Screws
1x Leash

Using Your Bindings

First Ride of the Day

Fully release the straps and push down the heel pedal until it’s locked and flush with the board. Put your foot in and crank the LSR ratchets (just like a regular binding).

Speed Entry

1. Kick – With the highback fully reclined, slide your foot firmly into the binding.
2. Click – Push down on the heel pedal to close the highback and engage the mechanism.
2x Offset Mounting Disks
8x Screws
1x Leash

Exit

1. Push down the release lever using your hand (not your boot!).
2. Maintain pressure on the lever while pulling your foot up against the ankle strap to release the mechanism.
2x Offset Mounting Disks
8x Screws
1x Leash
3. Slide your foot back, up and out.
2. Maintain pressure on the lever while pulling your foot up against the ankle strap to release the mechanism.
2x Offset Mounting Disks
8x Screws
1x Leash

Tips

• If snow accumulates, clear out the footbed and the area underneath the heel pedal before getting in.

• Do not use your boots to push the release lever! This can damage or break the lever.

• When skating or getting on the lift, fold the highback forward.

• On steep, uneven terrain or in deep snow, you can also use the ratchets to get in and out – just like a regular binding.

Adjusting the Forward Lean

Increasing the forward lean on your highback delivers more aggressive heelside control.

OG & LT Supermatic®
Fold open the lever. LT model – twist anti-clockwise to loosen. Move the block up or down, then tighten clockwise (LT) and fold the lever closed to lock in place.
Carbon Supermatic®
Use a screwdriver to loosen the inner screw, slide the block down to increase the angle, or up to reduce it, then re-tighten the screw.
2x Offset Mounting Disks
8x Screws
1x Leash

Attaching the Leash

Attach the leash to your front binding here. Connect it to your boot every time you go riding.
Use a screwdriver to loosen the inner screw, slide the block down to increase the angle, or up to reduce it, then re-tighten the screw.
2x Offset Mounting Disks
8x Screws
1x Leash

Maintenance

Once per season, apply low-temperature grease to the teeth of the locking mechanism as shown (two sides per binding, four locations total).
Use a screwdriver to loosen the inner screw, slide the block down to increase the angle, or up to reduce it, then re-tighten the screw.
2x Offset Mounting Disks
8x Screws
1x Leash

Warning

WARNING: Vibration, temperature changes and board flex can loosen mounting screws and other hardware. Ensure all screws are tight before every riding session, and check ratchets and components are in working order.